Reader-supported. If you buy through our links we may earn a commission. Disclosure

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

The Klein Tools 32767 3-in-1 SAE Impact Flip Socket is a 5-inch impact-rated socket for pros who switch between fastener sizes all day. It replaces a few loose adapters and bit holders with one tool. On paper, it suits anyone running an impact driver.

The flip design is what matters. One side has 1/4-inch shallow (driver) and 1/4-inch deep (bit holder) positionsand the other is 5/16-inch. The rare-earth magnet holds bits and hex head fasteners, which helps when you are working overhead or reaching into a tight space.

Quick verdict: A sensible one-tool option for impact driver users who want fewer loose parts in the bag.

  • Best for: Techs driving 1/4-inch and 5/16-inch hex fasteners with an impact driver.
  • Skip it if: You need other sizes, since this covers only 1/4-inch and 5/16-inch hex.
  • Key spec: Impact rated with a rare-earth magnet and a 5-inch shaft that fits Klein 32303 and 32304 handles.

Klein Tools 32767 Key Specs and What Comes in the Box

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

The main feature is the flip design. One end has a 5/16-inch hex socket. The other end has two 1/4-inch positions, a shallow one for driving and a deep one that works as a bit holder. You flip the tool to change jobs instead of reaching for a different one.

  • Drive: 1/4-inch quick connect for an impact driver
  • Rating: impact rated
  • Length: 5-inch shaft
  • Magnet: rare-earth, holds bits and hex head fasteners
  • Handle fit: Klein Tools 32303 and 32304 driver handles

The impact rating matters most. Standard bit holders and sockets can crack when an impact driver hammers on them, so you want one built for it. The 5-inch shaft gives you reach into recessed spotsand the magnet helps keep a hex head screw on the tip when you are working overhead or in a tight cabinet. The handle fit means the same piece can also go on a hand driver.

As for what comes in the box, the Klein Tools 32767 3-in-1 SAE Impact Flip Socket is described as a single socket. The listing does not mention bits, adapters or a case. Plan on supplying your own 1/4-inch bits for the bit holder end.

Does the 3-in-1 Flip Socket Really Speed Up Fastener Work?

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

Yes, if your work matches what it covers. The time savings come from not swapping tools. One shaft gives you a 5/16-inch hex on one side and two 1/4-inch positions on the other, so you flip it instead of digging through a pouch.

  • 5/16-inch hex on one side for hex head fasteners
  • 1/4-inch shallow position that works as a driver
  • 1/4-inch deep position that works as a bit holder
  • Rare-earth magnet that holds bits and hex head fasteners
  • Impact rated, with a 1/4-inch quick connect
See also  My Go-To Duct Knife: Klein Tools DK06 Review

For HVAC work that matters. Panel screws, hex head fasteners and the odd bit job often show up in the same service call. The magnet helps keep a fastener on the tip when you are reaching into a tight spot or working overhead. A screw that stays put is one you don’t have to chase.

The 5-inch shaft also fits Klein Tools 32303 and 32304 driver handles, so it is not tied to an impact driver. The limit is that it only covers those three sizes. Any other fastener still means another tool. On any flip socket I would check magnet hold and wear in the hex positions first, since those are what decide whether it keeps saving time.

Is the Klein 32767 Built to Survive Daily Jobsite Abuse?

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

The most useful fact is that Klein rates this socket for use on an impact driver. That matters because impact shock is what cracks or rounds out ordinary bit holders and sockets. If a tool in this class isn’t built for it, it won’t last through a week of driving fasteners.

The description doesn’t give the steel grade or hardness, so I can’t say more about how it’s made. Klein is a family-owned American company that has been making hand tools since 1857, which counts for something. A brand name still isn’t a durability spec. Here is what I’d check on any flip socket like this:

  • The 1/4-inch quick connect end, since it gets chucked in and out all day.
  • The rare-earth magnet, which has to keep holding bits and hex head fasteners even with metal shavings and grime on it.
  • The hex walls in the 5/16-inch, shallow 1/4-inch and deep 1/4-inch positions, where rounding or cracking shows up first.
  • The 5-inch shaft, which can bend if you lean on it at an angle.

The shaft also fits Klein 32303 and 32304 handles. Hand driving puts less shock on the tool than an impact does, so the impact rating is the real durability claim here.

Which Impact Drivers and Drills Fit the 5-Inch Shaft?

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

This socket is made for impact drivers with a 1/4-inch quick connect. That is the use Klein rates it for, so that is the fit to count on. The 5-inch shaft adds reach, which helps when the fastener sits back in a cabinet or behind a panel.

  • Impact drivers: the listing says it is impact rated and made for a 1/4-inch quick connect.
  • Klein handles: it also fits the Klein Tools 32303 and 32304 screwdriver handles.
  • Driver side: one side has a shallow 1/4-inch driver position and a deep 1/4-inch bit holder position.
  • Other end: the opposite side is 5/16-inch for hex head fasteners.
See also  I Finally Found Wire Labels That Actually Stick

Drills are a different story. The description never mentions drill chucks, so I would not assume it fits or holds up in one. If you plan to run it off a drill, check the shaft and your chuck yourself before you count on it.

The handle fit is a nice extra. You can use the same piece for hand work when an impact would be too much for the job. The rare-earth magnet holds bits and hex head fasteners in either setup.

How Does It Compare to a Standard Impact Socket Set?

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

A standard impact socket set wins on rangeand this one wins on convenience. The Klein Tools 32767 3-in-1 SAE Impact Flip Socket puts a 5/16-inch hex socket, a shallow 1/4-inch driver and a deep 1/4-inch bit holder in one piece. That covers a lot of the screw driving I see on HVAC panels and ductwork without digging through a case.

  • Sizes: 5/16-inch on one end, both 1/4-inch positions on the other.
  • Bit holding: the deep 1/4-inch side acts as a bit holder, which a standard socket cannot do.
  • Magnet: a rare-earth magnet holds bits and hex head fasteners.
  • Reach: a 5-inch shaft gets into recessed spots a short socket will not.
  • Handle fit: it also fits Klein 32303 and 32304 screwdriver handles.

A standard set covers many more fastener sizes, so this does not replace one for general bolt work. What it does is cut down the swapping on a single job. If most of your work is 5/16 hex screws and 1/4-inch bits, one flip tool on the impact driver saves time. If you turn a mix of bolt sizes, you still want the full set in the truck.

Which Jobs and Users Suit the Klein 32767 Best?

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

The Klein Tools 32767 suits techs who run an impact driver all day and want fewer loose parts in the pouch. One end gives you 1/4-inch shallow (driver) and 1/4-inch deep (bit holder) positions. The other end is 5/16-inch. On HVAC and general service work, those are the hex head sizes you run into most often.

  • Good fit: pros who switch between driving hex head fasteners and holding bitsand want to flip the tool instead of swapping accessories.
  • Good fit: jobs where the fastener sits in a recess. The 5-inch shaft gives you reachand the rare-earth magnet holds the fastener or bit in place.
  • Good fit: anyone who already carries Klein 32303 or 32304 screwdriver handles, since this shaft fits them.
  • Poor fit: work that needs hex sizes beyond 1/4-inch and 5/16-inch. You will still need other sockets.

A magnet matters more than it sounds. Starting a fastener one-handed overhead or inside a cabinet goes a lot easier when it stays on the tip. Check the magnet and the flip ends for wear over time, since that is where tools in this class tend to show it first.

See also  My Go-To Knee Pads for All-Day Job Site Comfort

Pros & Cons

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

Pros and Cons

Pros Cons
Three hex positions in one flip socket mean fewer loose pieces to carry. SAE sizing only, so metric hex fasteners need a different tool.
Rare-earth magnet holds both bits and hex head fasteners. Only 5/16 and 1/4 hex sizes, nothing bigger for larger fasteners.
Impact rated, so it is built for use on an impact driver. The deep 1/4 position is a bit holder, so you supply the bits.
1/4-inch quick connect makes swapping it in and out of an impact driver easy. Changing sizes means flipping the socket, an extra step versus a dedicated socket.
Five-inch shaft also fits Klein 32303 and 32304 driver handles. A five-inch shaft is long for cramped panel or equipment work.

Skip it if: you work mostly with metric fasteners, need hex sizes beyond 5/16 or want a short socket for tight spaces.

Frequently Asked Questions

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

Is the Klein Tools 32767 flip socket impact rated?

Yes, the Klein Tools 32767 is impact rated and made for use on an impact driver. It has a 1/4-inch quick connect for easy use on an impact driver. Impact use is hard on tools, so I always check for that rating before putting any socket or bit holder on one. This one lists it.

What sizes does the Klein Tools 32767 3-in-1 flip socket include?

It includes three hex sizes: 5/16-inch, 1/4-inch shallow (driver) and 1/4-inch deep (bit holder). The 1/4-inch shallow and deep positions are on one side and the 5/16-inch is on the other. You flip the socket to switch between them, which saves swapping tools when you move between fasteners.

Does the Klein Tools 32767 fit Klein screwdriver handles?

Yes, the 5-inch shaft also fits Klein Tools screwdriver handles Cat. Nos. 32303 and 32304. That gives you a hand-driven option when an impact driver is too much or will not fit. Confirm the handle fit against your own handle’s catalog number before you buy.

Does this Klein flip socket have a magnet to hold screws?

Yes, it has a rare-earth magnet that holds bits and hex head fasteners. That helps when you are working overhead or in a tight spot like an equipment cabinet and cannot afford to drop a screw. The description does not give magnet strength, so do not expect a specific holding force.

What is the warranty on the Klein Tools 32767?

The description does not state a warranty length, so check the listing or Klein Tools directly. Klein says it is a family-owned American company that has made hand tools since 1857. That is background, not a warranty term. Get the coverage details from the manufacturer before you buy if that matters to you.

Final Verdict

Klein Tools 32767 Review: One Flip Socket for 3 SAE Sizes

This is a narrow, practical tool. One flip socket gives you 5/16-inch on one side and 1/4-inch on the other, with shallow driver and deep bit holder positions. It is impact rated, with a 1/4-inch quick connect and a rare-earth magnet for bits and hex head fasteners. The 5-inch shaft also fits Klein 32303 and 32304 driver handles.

It suits a pro or serious DIYer who runs hex head fasteners with an impact driver and wants fewer loose pieces. A homeowner can use it, but may not need it. Look elsewhere if you need other sizes, since only these three SAE positions are listed. I can’t speak to long term durability. Tools in this class tend to wear at the hex ends and lose magnet grip, so check those first.

Check the current price on Amazon

Scroll to Top